Is your question not listed? Ask a question. About the Beko DIN Beko DIN specifications. Related product manuals. What do I do about a smelly dishwasher? In the case of a smelly dishwasher, you can take the following steps: - Clean the filters - Clean the spray arms - Clean the door rubbers - Run a hot wash program - Run an empty machine with a dishwasher cleaner. Do you have to pre-rinse the dishes? It is not recommended to rinse dirty dishes before placing them in the dishwasher. For the life cycle of the machine, it is better to put everything dirty in the dishwasher.
The grease on the dirty dishes is the lubrication for the pump in the machine. Starting 1. Select the programme and the temperature. Page Cleaning And Care After the program is finished 1. Open the loading door and take out the clothes.
Turn the water tap off. Cleaning and care Detergent drawer Remove any powder residue buildup in the drawer. To do this; 1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. Drain the water off into the container by pulling out the plug at the end of the hose. If the amount of water to be drained off is greater than the volume of the container, replace the plug, pour the water out, then resume the draining process.
Page Troubleshooting Troubleshooting Problem Cause Machine may have Program switched to self cannot be protection mode due to started or an infrastructure problem selected. There may be some water in your machine when you Water in the receive it. This is from the machine. Page 27 The water being taken Improper position of the in is directly drain hose. No water can This is not a problem. The be seen in water level is not visible the machine from the outside of the during machine.
Page 28 In the case of a paused countdown while taking in water: Timer will not countdown until the machine is filled with the correct amount of water. In the case of a paused countdown at the heating step: It continuously Time will not count washes. Page 29 - Using insufficient amount of detergent for a long time, - Washing at low Washing temperatures for a long performance is time, poor: - Using insufficient Laundry turns amount of detergent for gray hard waters soil can stick to the laundry , - Using excessive amount of detergent detergent can stick to the laundry.
Page 30 The amount, brand and storage conditions of the detergent used might not be appropriate. Detergent might have been put in the wrong compartment.
Machine filter may be It does not clogged. Drain hose may be folded. Check the drain hose. Intermediate spins may be skipped. Page 31 If you put detergent in the prewash compartment although you have not selected a prewash cycle, the machine can take this detergent during rinsing or softener step.
You may have added too much softener. The detergent dispenser might be problematic. Water may be siphoned pulling the softener into the washer early during the fill or rinse cycles. There might be problems with the valves.
Page 32 The plug might not be plugged in the mains outlet. Machine does Fuse may have blown. No light is on. Electricity may be cut off.
The machine did not start after the program was The front door may be selected and ajar. If they are not, call a qualified plumber to have any necessary arrangements carried out. There may be a risk of being scalded due to high washing temperatures! Otherwise, there may be the risk of flooding and possible injury due to the hot water. The door will be ready to open just a few minutes after the washing cycle comes to an end.
There is the risk of electric shock! Always disconnect from the mains by unplugging before cleaning. Never unplug by pulling on the cable, always pull out from the plug only. Do not operate the. Turn off the machine, unplug it, turn off the water tap and contact an authorized service agent. Keep children away from the machine when it is operating. Do not let them tamper with the machine. Connect the power cord to the appropriate electrical socket with an equivalent current rating indicated on the rating plate at the front of the machine behind the kick plate.
After removing the plug from its transit position, please insert the plug seal to prevent water spillage entering the machine. Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating label corresponds to your electricity supply.
We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket in a readily accessible position. Should the mains lead of the appliance become damaged or need replacing at any time, it must be replaced by a. If the fitted moulded plug is not suitable for your socket, then the plug should be cut off and an appropriate plug fitted. Destroy the old plug, which is cut off as a plug with a bared cord could cause a shock hazard if inserted into a socket elsewhere in the house.
The moulded plug on this appliance incorporates a 13A fuse. Do not forget to refit the fuse. In the event of losing the fuse cover, the plug must not be used until a replacement fuse cover has been fitted.
Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug. Fuse covers are available from any good electrical store. As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug, proceed as follows:.
With the alternative plugs a 13A fuse must be fitted either in the plug or adaptor or in the main fuse box. If in doubt contact a qualified electrician. Tilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. C Transportation safety bolts must be removed before operating the washing machine!
Otherwise, the machine will be damaged! Remove transportation safety bolts by turning them gently. Fit the covers supplied in the bag with the Operation Manual into the holes on the rear panel. C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future. C Never move the appliance without the transportation safety bolts properly fixed in place! Install the appliance in environments which have no risk of freezing, in a stable and level position.
C The floor must be capable of carrying the load on it! C If the washing machine and a drier are placed on top of each other, their approximate weight together may reach kg when they are full. C Do not use any tools to loosen the lock nuts.
Otherwise, they can be damaged. Manually by hand loosen the lock nuts on the feet. Adjust them until the machine stands level and firm. Important: Tighten all lock nuts up again. Practically, it is necessary to have 10 — 80 liters of water flowing from the tap in one minute to have your machine run smoothly.
Attach a pressurereducing valve if the water pressure is higher.
0コメント